Evaporative
Swamp Cooler Replacement Parts For
Nearly All Brands of Evaporative Swamp Coolers
Motors, Pumps, Aspen Pads, Pad Retaining Wires, Floats, Pulleys, Bearings,
Cooler Covers,
MasterCool Pads, UltraCool Pads, AeroCool Pads
Most Commonly Used Replacement Evaporative
Swamp Cooler Parts Are Available From Us
Power
Clean Installation Instruction
CAUTION:
Disconnect
electrical power to cooler before installing your POWER-CLEANŽ
system or servicing cooler
Installation
must comply with cooler manufacturer's specifications and
all applicable building and electrical codes.For safety
against electrical shock, cooler cabinet, blower motor, pump(s)
and switch(es) must all be properly grounded.
INSTALLATION
PROCEDURE:
Disconnect
Electricity to Evaporative Cooler.
Unplug
Pad Pump
Place
Pump Screen Onto POWER-CLEANŽ
Pump.Mount
POWER-CLEANŽ Pump Inside Cooler. Secure pump to blower housing
with mounting bracket.
Install
Hose Adapter Into Overflow Pipe. Place proper
end of hose adapter into overflow pipe. See markings on hose
adapter.
Attach
1/2" Hose From POWER-CLEANŽ Pump To Hose Adapter. Securely
attach hose onto pump. Connect other end of hose onto hose adapter.
Avoid kinking hose -- cut hose if deemed necessary.
Plug-In
POWER-CLEANŽ Pump. Note the specially integrated plug and
receptacle on the POWER-CLEANŽ pump cordset.
Plug-In
Pad Pump. Plug your pad pump into the special POWER-CLEANŽ
pump receptacle.
Connect
Piping To Remove Cooler Water. Do not allow cooler water
to run onto roof. Connect garden hose, or 3/4" PVC piping
from underside of cooler drain to an appropriate drain site
on the ground. Use of 45 degree elbows instead of 90 degree
elbows is recommended. This will prevent unsightly roof stains
as well as potentially damaging effects to roof shingles.
Reconnect
Electricity to Evaporative Cooler.
OPERATING:
Your
POWER-CLEANŽ system automatically removes the water
in your cooler once *every 8 hours that the cooler pad
pump is "ON". This periodic draining replaces
the 'hard' water that naturally develops in the cooler with
clean, fresh water in a consistent manner. The result is decreased
scale build-up, longer pad life, less cooler maintenance and
lower water usage (compared to a standard bleed-off system).
IMPORTANT:
POWER-CLEANŽ
drains the water depth to less than 1/2 inch.
During
the POWER-CLEANŽ draining cycle, both purge and pad pumps
are "on".
CONTENTS:
1
POWER-CLEANŽ Purge Pump
1
Mounting Bracket
1
Pump Screen
*1
Pump Hose (1/2" I.D., 30 inches long)
1
Hose Adapter (Purge Pump Hose to Overflow Pipe)
Note
for Tucson, Arizona Area Installations:
Certain
building/electrical codes require the use of a "P-26
Fuse Box", such as the G.E. Model No. T-U261F rainproof
power outlet fuse box when wiring a cooler.
When
using this fuse box, a fuse rated at 1.6 Amp might be required
for proper operation of the POWER-CLEANŽ system vs.
the smaller 1.25 Amp fuse. These fuses are a type S time
delay and must be used ahead of the cooler pump and POWER-CLEANŽ
system.
LIMITED
WARRANTY:
Purge
Pump is warranted under normal use and recommended maintenance
for 2 years from date of sale to user. In event of defect
or failure, replacement is made through your authorized dealer
or retailer.
Reason
for replacement, purchase date, and sales receipt must
accompany pump returned for replacement.
Warranty
is void if pump has been abused, altered, water damaged or
improperly installed.
We
do not pay the cost of a service call at the site of installation
to diagnose cause of trouble, or the cost of labor or transportation
to replace a defective pump.
We
are not responsible for any incidental or consequential damage
resulting from any malfunction unless required to do so by
state law.
