 |
|
|
MasterCool,
UltraCool & AeroCool Cooler Pads
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
THE ULTIMATE COOLING MEDIA FOR SINGLE INLET COOLERS Long Life - High Air Velocity - Energy Efficient Consistent Performance 50% heavier paper holds more water and lasts longer Independent lab and field tests verify highest efficiency Fast wet-out Engineered for optimal performance and longevity...Cellulose base impregnated with plastic resins and anti-rot agents...Durable and easy to install. |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Pad |
P/N
3440 |
Free Shipping |
|
Pad |
41 1/4 x 29 x 8 UltraCool ADA 70 or ASA 70 or AUA 70 |
Free Shipping |
|
Pad |
(Champion Mfg Part) 41 1/4 x 22 1/2 x 12 UltraCool ADA 5012 or ASA 5012 |
Free Shipping |
|
Pad |
(Champion Mfg Part) 41 1/4 x 29 x 12 UltraCool ADA 7012 or ASA 7012 |
|
|
|
||
|
Pad |
P/N
3437 |
Free Shipping |
|
Pad |
40 x 30 x 8 AeroCool 6800 |
Free Shipping |
|
AeroCool
Window Cooler Model
BW 5500 Brisa |
||
|
3"
Thick
Pad |
P/N
3436
(4 pcs - 10 x 26 1/8 x 3) MasterCool Window View Pad MW 5500 |
$150
Total Cost
Free Shipping |
|
MasterCool
Pads |
||
|
Pad |
40 x 23 x 8 MasterCool Fits EC 430 - EC 440 MC 43 - MC 44 PM 100 |
Free Shipping |
|
Pad |
40 x 28 x 8 MasterCool Fits EC 630 - EC 640 MC 63 - MC 64 PM 200 |
Free Shipping |
|
|
||
|---|---|---|
|
Pad |
40 x 23 x 12 MasterCool Fits HPC 430 - HPC 440 HC 43 - HC 44 PM 120 |
Free Shipping |
|
Pad |
40 x 28 x 12 MasterCool Fits HPC 630 - HPC 640 HC 63 - HC 64 PM 220 |
Free Shipping |
|
Industrial
Model MasterCool Pads Below Free
Shipping For Quantities Show Below Email For Special Quote on Very Large Quantities Note:
Two Pads Required For Dual Inlet Coolers |
||
|
8"
Thick
Pad |
P/N
3460
40 x 37 3/4 x 8 MasterCool PM 300 |
One
Pad Set Two
Pad Sets |
|
Pad |
48 x 44 5/8 x 8 MasterCool PM 400 |
One
Pad Set Two
Pad Sets |
|
Pad |
48 x 44 5/8 x 12 MasterCool PM 500 |
One
Pad Set Two
Pad Sets |
Note:
Two Pads Required For Dual Inlet Coolers
(Models MD 628 - MS 628 - MU 628)
One Pad Required For Single Inlet Coolers
(Models MD 524 - MS 524 - MU 524)
Click
Here For:
Installation Instructions
Evaporative
Swamp Cooler Replacement Parts
For
Nearly All Brands of Evaporative Swamp Coolers
Motors, Pumps, Aspen Pads, Floats, Pulleys, Bearings,
Cooler Covers,
MasterCool Pads, UltraCool Pads, AeroCool Pads
Most Commonly Used Replacement Evaporative Swamp Cooler
Parts
Are Available From Us
Rigid
Cooling Media Pad
Pad
is not one piece
Comes in Sections
2 - 4 sections per set
to make correct width
8"
& 12" Thick Pads
The Most Efficient type of
Cooler Pad Made
For
MasterCool
UltraCool
& AeroCool Coolers
Click
Here For:
Installation Instructions
Note:
New Rigid
Cooling Media Pad
type pads will emit a slight odor when first installed
Click
Here To See Why
Rigid
Cooling Media Pad
Pad
is not one piece
12"
Wide Sections
with one smaller section
to make correct width
8"
& 12" Thick Pads
The Most Efficient type of
Cooler Pad Made
MasterCool
MW 5500 Window View
Pad
is not one piece.
(4 PCS) 10" x 26 1/8" x 3" Sections
Rigid
Cooling Media Pad
Pad
is not one piece
12"
Wide Sections
with one smaller section
to make correct width
8"
& 12" Thick Pads
The Most Efficient type of
Cooler Pad Made
Rigid
Cooling Media Pad
Pad
is not one piece
12"
Wide Sections
with one smaller section
to make correct width
8"
& 12" Thick Pads
The Most Efficient type of
Cooler Pad Made
Click
Here For:
Installation Instructions
Note:
New Rigid
Media Pads
will emit a slight odor when first installed
Click Here To See Why
|
WHY
IS THERE AN ODOR FROM MY NEWLY INSTALLED COOLER PAD? When these pads are first wet out a slight odor may occur from the dust created when the pad is manufactured and cut to size. THIS ODOR IS NOT TOXIC OR HARMFUL. The operation of this type cooling pad requires a wet out period (typically several hours without airflow) followed by draining and refilling the sump water pan. This will remove the small amount of residue in the media that would be the source of the odor. This operation may have to be repeated on larger systems that do not drain completely. All evaporative cooling systems have odor problems related to the system cleanliness. This is how 'swamp coolers' first got its name. When left UN-cleaned, they would start to smell like a swamp. All cooling media require cleaning, both initially, and ongoing. All cooling pads of this type are manufactured using the same base resin materials and have the same odor associated with them. All new cooler pads have a 'new pad' odor that dissipates with use. Once the pads are 'broken in', this odor will disappear. The once active ingredients in the paper of the cooling pad are rendered inert during the manufacturing processing, however the odor from these materials lingers until the pads are washed clean by the wetting process after installation.
|
|
We
Accept All Credit Cards
PayPal is Preferred  |
|||||||
|
Contact
Us Please
Use Phone To Place Orders Only We
Reply To All E-mail Requests
Copyright
© 1999 KennsPenns All Rights Reserved
|
|||||||
